Clamps Accommodate Metal Roof Panels With a Horizontal Seam

S-5-H clamp and S-5-H Mini clamp

S-5-H clamp and S-5-H Mini clamp

S-5! introduces two clamps for metal roof panels. The S-5-H clamp was developed to securely and cost-effectively accommodate metal roof panels with a horizontal seam. The S-5-H allows for attachment to a horizontal seam on the vertical leg of the seam.

The clamp’s two-piece design allows it to be installed anywhere along the length of the rib, simplifying installation. Just place the clamp on the seam, slide the insert piece into place and tighten the setscrews. After the clamp is installed, affix ancillary items using the top stainless steel bolt provided. The S-5-H can be used with the S-5! ColorGard snow retention system and other heavy-duty applications.

The S-5-H Mini is a bit shorter than the S-5-H and has one setscrew rather than two. The mini can be used for attaching a variety of rooftop accessories, including signs, walkways, satellite dishes, antennas, rooftop lighting, lightning protection systems, solar arrays, exhaust stack bracing, conduit, condensate lines and mechanical equipment. S-5! mini clamps are not compatible with S-5! SnoRail/SnoFence or ColorGard snow retention systems.

Add Components to Your ColorGard Snow Retention System

S-5!'s SnapClip II

S-5!’s SnapClip II

SnapClip II or SnapClip III are optional components that can be added to your S-5! ColorGard snow retention system to further retard the migration of snow. It has a special integrated rubber “foot” to prevent abrasion of the panel’s finish. SnapClip snaps onto the back of the crossmember and extends down to the flat of the roofing panel.

Snap the SnapClip onto your ColorGard crossmember after installation. One or two clips are used between seams (please visit www.S-5.com for details). Mount the SnapClip to the back of the crossmember using the lock that results with the rubber “foot” resting properly on the panel surface. When applying downward pressure on the part, the “toe” should engage the surface of the panel just before the “heel.” Screw SnapClip into place utilizing the provided stainless steel self-tapping screw.

SnapClip II has two locks and is especially made for seam heights of 1 inch (25 mm) and 1 3/4 inch (44.5 mm) snap. It will also fit 2-inch (51-mm) vertical seams but not 2 inch (51 mm) horizontal.

SnapClip III has three different locks and will work on seam heights of 1 3/4 inch (44.5 mm) up to 3 inches (76 mm).

Snow-retention Components Further Slow Snow from Sliding Off a Roof

SnapClip II from S-5!

SnapClip II from S-5!

SnapClip, SnapClip II or SnapClip III are optional components that can be added to your S-5! ColorGard snow retention system to further retard the migration of snow. It has a special integrated rubber “foot” to prevent abrasion of the panel’s finish. SnapClip snaps onto the back of the crossmember and extends down to the flat of the roofing panel.

Snap the SnapClip onto your ColorGard crossmember after installation. One or two clips are used between seams. Mount the SnapClip to the back of the crossmember using the lock that results with the rubber “foot” resting properly on the panel surface. When applying downward pressure on the part, the “toe” should engage the surface of the panel just before the “heel.” Screw SnapClip into place utilizing the provided stainless steel self-tapping screw.

SnapClip II has two locks and is especially made for seam heights of 1 inch (25 mm) and 1 3/4 inch (44.5 mm) snap. It will also fit 2-inch (51 mm) vertical seams but not 2-inch (51 mm) horizontal.

SnapClip III has three different locks and will work on seam heights of 1 3/4 inch (44.5 mm) up to 3 inches (76 mm).

SnapClip should not be used on copper roofs.